What are the precautions for advertising engraving machine materials?

1. Do not install this device during lightning or thunder. Do not install the power outlet in a damp place. Do not touch the uninsulated power cord.

2, the machine operators must undergo strict training and operation must pay attention to personal safety and machine safety, and operate the computer engraving machine in strict accordance with the operating procedures.

3, the power supply voltage requirements 210V-230V, if the power supply voltage is unstable or there are high-powered electrical equipment around, please be sure to choose the regulated power supply under the guidance of professional and technical personnel.

4, engraving machine, control cabinet must be grounded, can not be plugged in data cable.

5, the operator should not wear gloves, it is best to wear protective goggles.

6. The mechanical body is a part of the aviation aluminum casting of the steel structure gantry, which is relatively soft. When installing the screws (especially when installing the engraving motor), do not use too much force to prevent the wire from slipping.

7. The tool must be installed and clamped to keep the tool sharp. The blunt knife will reduce the quality of the engraving and overload the motor.

8. Do not put your fingers into the working range of the tool. Do not remove the engraving head and use it for other purposes. Materials containing stone white cotton are not processed.

9. Do not exceed the scope of machining. When the machine is not working for a long time, the power must be cut off. When the machine is moving, it must be carried out by a professional.

10. If the machine is abnormal, please refer to the troubleshooting chapter of the operation manual or contact the dealer to solve the problem;

How does the advertising engraving machine save time?

1. When engraving the dot pattern, it is appropriate to reduce the resolution. The purpose is to speed up the work and save time.

Note: There is a theoretical knowledge that the processing depth of a laser machine is proportional to speed and power, so we can speculate that if the power is the same, the faster the depth, the deeper the engraving depth, and the deeper, the opposite. So we should try our best to increase the speed and power to shorten the time.

2. Another point of saving time is that if a large number of products of the same size and size are required in actual work, the maximum width of the X direction should not exceed 300 mm, which can speed up the round trip speed of the laser head, thereby increasing the speed. Time is saved.

Advertising engraving machine spindle motor bearing rust?

The reason why the advertising engraving machine produces rust of the motor bearing is very complicated. It may be that the imported bearing is not well treated by rust, or it may be caused by moisture and rust caused by paint mist. At present, most of the motor manufacturers use insulating paint to volatilize the main acid components:

1. The acid component formed after the lacquer cured product is decomposed by water. The main acid component produced by the insulating varnish is formic acid, and the amount of formic acid generated is closely related to the degree of rust occurrence.

2. Low-molecular lacquer raw material acid component (anhydrous o- and terephthalic acid, anhydrous maleic acid, trans-butenedioic acid) which has not reacted.

3. The acid component formed during curing of the paint (from formaldehyde to formic acid when the phenolic denatured paint is used).

4. Lower fatty acids (formic acid, acetic acid) produced by heat or oxidative decomposition.What are the precautions for advertising engraving machine materials?

1. Do not install this device during lightning or thunder. Do not install the power outlet in a damp place. Do not touch the uninsulated power cord.

2, the machine operators must undergo strict training and operation must pay attention to personal safety and machine safety, and operate the computer engraving machine in strict accordance with the operating procedures.

3, the power supply voltage requirements 210V-230V, if the power supply voltage is unstable or there are high-powered electrical equipment around, please be sure to choose the regulated power supply under the guidance of professional and technical personnel.

4, engraving machine, control cabinet must be grounded, can not be plugged in data cable.

5, the operator should not wear gloves, it is best to wear protective goggles.

6. The mechanical body is a part of the aviation aluminum casting of the steel structure gantry, which is relatively soft. When installing the screws (especially when installing the engraving motor), do not use too much force to prevent the wire from slipping.

7. The tool must be installed and clamped to keep the tool sharp. The blunt knife will reduce the quality of the engraving and overload the motor.

8. Do not put your fingers into the working range of the tool. Do not remove the engraving head and use it for other purposes. Materials containing stone white cotton are not processed.

9. Do not exceed the scope of machining. When the machine is not working for a long time, the power must be cut off. When the machine is moving, it must be carried out by a professional.

10. If the machine is abnormal, please refer to the troubleshooting chapter of the operation manual or contact the dealer to solve the problem;

How does the advertising engraving machine save time?

1. When engraving the dot pattern, it is appropriate to reduce the resolution. The purpose is to speed up the work and save time.

Note: There is a theoretical knowledge that the processing depth of a laser machine is proportional to speed and power, so we can speculate that if the power is the same, the faster the depth, the deeper the engraving depth, and the deeper, the opposite. So we should try our best to increase the speed and power to shorten the time.

2. Another point of saving time is that if a large number of products of the same size and size are required in actual work, the maximum width of the X direction should not exceed 300 mm, which can speed up the round trip speed of the laser head, thereby increasing the speed. Time is saved.

Advertising engraving machine spindle motor bearing rust?

The reason why the advertising engraving machine produces rust of the motor bearing is very complicated. It may be that the imported bearing is not well treated by rust, or it may be caused by moisture and rust caused by paint mist. At present, most of the motor manufacturers use insulating paint to volatilize the main acid components:

1. The acid component formed after the lacquer cured product is decomposed by water. The main acid component produced by the insulating varnish is formic acid, and the amount of formic acid generated is closely related to the degree of rust occurrence.

2. Low-molecular lacquer raw material acid component (anhydrous o- and terephthalic acid, anhydrous maleic acid, trans-butenedioic acid) which has not reacted.

3. The acid component formed during curing of the paint (from formaldehyde to formic acid when the phenolic denatured paint is used).

4. Lower fatty acids (formic acid, acetic acid) produced by heat or oxidative decomposition.